 |
| Quantity: | |
|---|---|
YDL353
BOEEP
YDL
Product Description
BOEEP pre-thickening screw press dewatering unit is aimed at treating low concentration sludge. It integrates the functions of thickening and dewatering in one unit. The concentration range can be from 2500mg/L to 20000mg/L, thus the investment can be reduced a lot.
Main Structure
BOEEP pre-thickening screw press dewatering unit is composed of pre thickening mixing system, screw body, driving device, filtrate receiver and frame.
 1-Pre Thickening Mixing system The pre concentration system is composed of the pre concentration system (Figure 1), the mixing blades and the concentrated box. The mixing system is used to make the sludge and polymer fully mixed in the thickening tank, the sludge can be flocculated to be gathered together, meanwhile, some of the water will be filtrated in the thickening system due to the gravity function, and the formed flocs will be transported to the screw body to press and dewater. There are sludge inlet, overflow port, polymer feed port and vent nozzle in mixing tank. Also there is the level adjusting device to adjust the sludge inleting amount. |
2-Screw body
Screw body is composed of fixed rings, moveable rings, screw shaft, screw, gasket and lots of junction plate. The front part of the main body is the thickening part, and the ending part is dewatering part. So the thickening and dewatering of the sludge can be finished in one canister. Sludge will be transported to the dewatering department after being thickened in the thickening department. In the advancing process, great pressure has been produced because of the gradually decreasing filter spacing and screw distance, and the back platen clogging. Then the volume decreases continuously, and the purpose of fully dewatering will be achieved.
3-Driving device
Drive device is the power source of the equipment, and the performance of drive device can affect the equipment performance directly. For this reason, the motor our company adopts has a superior performance with IP55 and F level. Frequency conversion starting and speed control mode can suit for different application conditions to avoid the impact of the load.
4-Filtrate receiver
Filtrate receiver, welded by plate, is used to collect filtrate pressed by screw body. Filtrate receiver is welded to the side plates directly, and there are flanges on the side to connect the external devices.
Working Principle
When the pre-thickening screw press dewatering unit operates, sludge will be transported to the mixing tank by sludge feed pump, at the same time, the solid polymer has been added to the mixing tank quantitatively by the polymer feed pump. Mixing motor drives the whole mixing system to make the sludge and polymer fully mixed and then flocs will be produced. When the liquid level arrives at the superior level of the liquid level sensor, the liquid level sensor gets the signal to make the motor of screw body operates, then begins to press the sludge which has flows into the screw body. Sludge will be transported to the outlet step by step by the effect of screw shaft; filtrate will flow out by the space of fixed annular plates and moveable annular plates.
Application
The pre-thickening screw press dewatering unit can be widely used for dewatering sludge of municipal administration wastewater, food, beverage, drink, slaughtering and breeding, printing, petrochemical engineering, papermaking, tannery and pharmaceutical. Besides, we continuously offer customerized sollutions for spacial requirements of customers.
Innovative structure design makes it possible that the device can be used for all kinds of sludge with high or low density, especially the sludge with oil, and it can be named the invincible opponent to dewater the sludge with oil.
Technical Parameters
| Parameter design | |
| Type：YDL353 | Protection Level：IP55 F |
| Dimension：L4700×W1950×H2130（mm） | Power Supply：380V/3/50Hz or customize |
| Inlet sludge concentration：2500~20000mg/L | Outlet sludge moisture content：75-85% |
| Capacity：240-360kgds/h | Polymer feeding rate：DS 0.2～1% |
| Power：4.8kw | Flush water：180L/h |
| Water supply pressure：≥0.2MPa | Equipment weight：3500kg |
| Screw body | Pre thickening mixing system |
| Diameter × Length：Φ350×2800(mm) | Dimension：L1000×W1000×H1400(mm) |
| Quantity：3pcs | Volume：1400L |
| Material：Plate: SUS304/ Screw Shaft: SUS304 | Material：SS304 |
| Motor Power：1.1×3kW | Motor power：1.5kw |
| Electrical Cabinet | |
| 1. Frequency converting controls dewatering body; | |
| 2. Controls polymer mixing device; | |
| 3. Realize the switch of automatic operation and manual operation. | |
Model Choice
Technical Specification
Product Details
Object Site
Product Description
BOEEP pre-thickening screw press dewatering unit is aimed at treating low concentration sludge. It integrates the functions of thickening and dewatering in one unit. The concentration range can be from 2500mg/L to 20000mg/L, thus the investment can be reduced a lot.
Main Structure
BOEEP pre-thickening screw press dewatering unit is composed of pre thickening mixing system, screw body, driving device, filtrate receiver and frame.
1-Pre Thickening Mixing system The pre concentration system is composed of the pre concentration system (Figure 1), the mixing blades and the concentrated box. The mixing system is used to make the sludge and polymer fully mixed in the thickening tank, the sludge can be flocculated to be gathered together, meanwhile, some of the water will be filtrated in the thickening system due to the gravity function, and the formed flocs will be transported to the screw body to press and dewater. There are sludge inlet, overflow port, polymer feed port and vent nozzle in mixing tank. Also there is the level adjusting device to adjust the sludge inleting amount. |
2-Screw body
Screw body is composed of fixed rings, moveable rings, screw shaft, screw, gasket and lots of junction plate. The front part of the main body is the thickening part, and the ending part is dewatering part. So the thickening and dewatering of the sludge can be finished in one canister. Sludge will be transported to the dewatering department after being thickened in the thickening department. In the advancing process, great pressure has been produced because of the gradually decreasing filter spacing and screw distance, and the back platen clogging. Then the volume decreases continuously, and the purpose of fully dewatering will be achieved.
3-Driving device
Drive device is the power source of the equipment, and the performance of drive device can affect the equipment performance directly. For this reason, the motor our company adopts has a superior performance with IP55 and F level. Frequency conversion starting and speed control mode can suit for different application conditions to avoid the impact of the load.
4-Filtrate receiver
Filtrate receiver, welded by plate, is used to collect filtrate pressed by screw body. Filtrate receiver is welded to the side plates directly, and there are flanges on the side to connect the external devices.
Working Principle
When the pre-thickening screw press dewatering unit operates, sludge will be transported to the mixing tank by sludge feed pump, at the same time, the solid polymer has been added to the mixing tank quantitatively by the polymer feed pump. Mixing motor drives the whole mixing system to make the sludge and polymer fully mixed and then flocs will be produced. When the liquid level arrives at the superior level of the liquid level sensor, the liquid level sensor gets the signal to make the motor of screw body operates, then begins to press the sludge which has flows into the screw body. Sludge will be transported to the outlet step by step by the effect of screw shaft; filtrate will flow out by the space of fixed annular plates and moveable annular plates.
Application
The pre-thickening screw press dewatering unit can be widely used for dewatering sludge of municipal administration wastewater, food, beverage, drink, slaughtering and breeding, printing, petrochemical engineering, papermaking, tannery and pharmaceutical. Besides, we continuously offer customerized sollutions for spacial requirements of customers.
Innovative structure design makes it possible that the device can be used for all kinds of sludge with high or low density, especially the sludge with oil, and it can be named the invincible opponent to dewater the sludge with oil.
Technical Parameters
| Parameter design | |
| Type：YDL353 | Protection Level：IP55 F |
| Dimension：L4700×W1950×H2130（mm） | Power Supply：380V/3/50Hz or customize |
| Inlet sludge concentration：2500~20000mg/L | Outlet sludge moisture content：75-85% |
| Capacity：240-360kgds/h | Polymer feeding rate：DS 0.2～1% |
| Power：4.8kw | Flush water：180L/h |
| Water supply pressure：≥0.2MPa | Equipment weight：3500kg |
| Screw body | Pre thickening mixing system |
| Diameter × Length：Φ350×2800(mm) | Dimension：L1000×W1000×H1400(mm) |
| Quantity：3pcs | Volume：1400L |
| Material：Plate: SUS304/ Screw Shaft: SUS304 | Material：SS304 |
| Motor Power：1.1×3kW | Motor power：1.5kw |
| Electrical Cabinet | |
| 1. Frequency converting controls dewatering body; | |
| 2. Controls polymer mixing device; | |
| 3. Realize the switch of automatic operation and manual operation. | |
Model Choice
Technical Specification
Product Details
Object Site
