 |
| Quantity: | |
|---|---|
ZDY2.0
BOEEP
ZDY
Product Introduction of Sludge Belt Filter Press
There are two parts compose the process system of sludge belt filter press. One part is a rotary drum, which takes responsibility for concentration. The other part is belt filter press part, which performs dehydration. This machine is mainly used for processing the sludge which is not concentrated in the thickening pool (such as A/O residual sludge).
Structure of Sludge Belt Filter Press
BOEEP sludge belt filter press machine is composed of conditioning tank, concentrating rotary drum and belt filter, when the flocculated sludge is fed into the rotary thickening drum, the thickened sludge flows from the rotary drum gap, washing device is set on the top of the rotary drum, which is to wash the drum. After being thickened, the sludge is distributed and feed onto the filter belt thoroughly. After pressed by the gravity dewatering zone, wedge compression zone, pre-pressing dewatering zone, low pressure dewatering zone, middle pressure dewatering zone, high pressure shear dewatering zone etc, the presser is put onto the sludge along the belt forwarding direction consistently, and the sludge cake will be output at the outlet port.
Advantages of Sludge Belt Filter Press
The surface has been treated as anticorrosion and painted with beautiful appearance. The structure is strong and durable.
Press roller: SUS304, reinforced welding, machined by fine processing, enough strength.
Belt cloth: GKD, good durability and excellent corrosion resistance.
Adopting advanced technical design ideas, combined with years of design experience and integrated design, Belt Filter Press can run stably, no shock, no vibration and no noise.
Belt position correcting system: automatic continuous detection, extend belt’s life.
Air pressure control device: the filter cloth tensioned by cylinder runs in its scope stably without leakage, high security.
Control panel: Omron or Schneider. PLC adopts Siemens, easy operation and maintenance.
Flocculator tank: Adopts different layout with different sludge inlet concentration, to mix the polymer and sludge thoroughly.
Technical Parameters of Sludge Belt Filter Press
| Model：ZDY2.0 | Filter belt width (mm)：B=2000mm |
| Capacity (m3/hr)：Q=12-20m3/h | D.S. Dried Sludge （kg/h）:180-260kgds/hr |
| Sludge cake moisture content (%)：75-85% | Press section filter belt speed (m/min)：1-7m/min |
| Motor power：2.05kw | Motor protection grade：IP55 |
| Motor insulation level：F | Power：380V，50HZ，3 |
| Flushing quality (m3/hr)：20m3/h | Flushing pressure (MPa)：0.6Mpa |
| Gas cylinder pressure：0.45Mpa | Speed control mode of driving mode：Frequency control |
Specification & Model Data of Sludge Belt Filter Press
Product Details of Sludge Belt Filter
Project Site of Sludge Belt Filter Press
Product Introduction of Sludge Belt Filter Press
There are two parts compose the process system of sludge belt filter press. One part is a rotary drum, which takes responsibility for concentration. The other part is belt filter press part, which performs dehydration. This machine is mainly used for processing the sludge which is not concentrated in the thickening pool (such as A/O residual sludge).
Structure of Sludge Belt Filter Press
BOEEP sludge belt filter press machine is composed of conditioning tank, concentrating rotary drum and belt filter, when the flocculated sludge is fed into the rotary thickening drum, the thickened sludge flows from the rotary drum gap, washing device is set on the top of the rotary drum, which is to wash the drum. After being thickened, the sludge is distributed and feed onto the filter belt thoroughly. After pressed by the gravity dewatering zone, wedge compression zone, pre-pressing dewatering zone, low pressure dewatering zone, middle pressure dewatering zone, high pressure shear dewatering zone etc, the presser is put onto the sludge along the belt forwarding direction consistently, and the sludge cake will be output at the outlet port.
Advantages of Sludge Belt Filter Press
The surface has been treated as anticorrosion and painted with beautiful appearance. The structure is strong and durable.
Press roller: SUS304, reinforced welding, machined by fine processing, enough strength.
Belt cloth: GKD, good durability and excellent corrosion resistance.
Adopting advanced technical design ideas, combined with years of design experience and integrated design, Belt Filter Press can run stably, no shock, no vibration and no noise.
Belt position correcting system: automatic continuous detection, extend belt’s life.
Air pressure control device: the filter cloth tensioned by cylinder runs in its scope stably without leakage, high security.
Control panel: Omron or Schneider. PLC adopts Siemens, easy operation and maintenance.
Flocculator tank: Adopts different layout with different sludge inlet concentration, to mix the polymer and sludge thoroughly.
Technical Parameters of Sludge Belt Filter Press
| Model：ZDY2.0 | Filter belt width (mm)：B=2000mm |
| Capacity (m3/hr)：Q=12-20m3/h | D.S. Dried Sludge （kg/h）:180-260kgds/hr |
| Sludge cake moisture content (%)：75-85% | Press section filter belt speed (m/min)：1-7m/min |
| Motor power：2.05kw | Motor protection grade：IP55 |
| Motor insulation level：F | Power：380V，50HZ，3 |
| Flushing quality (m3/hr)：20m3/h | Flushing pressure (MPa)：0.6Mpa |
| Gas cylinder pressure：0.45Mpa | Speed control mode of driving mode：Frequency control |
Specification & Model Data of Sludge Belt Filter Press
Product Details of Sludge Belt Filter
Project Site of Sludge Belt Filter Press
